http://www.murata.com/ data sheet ! note: 1. this datasheet is downloaded from the website of murata manufacturing co., ltd. therefore, it?s specifications are subject t o change or our products in it may be discontinued without advance notice. please check with our sales representatives or product engineers bef ore ordering. 2. this datasheet has only typical specifications because there is no space for detailed specifications. therefore, please appr ove our product specifications or transact the approval sheet for product specifications before ordering. 1 o this data sheet is applied for chip common mode choke coil used for general electronics equipment for your design. 2011.7.7 noise suppression products/emi suppression filters > common mode choke coil > film type 1.0 0.1 1.25 0.1 t 0.3 0.1 0.55 0.1 0.25 +0.1 ? 0.05 (1) (2) (3) (4) (in mm) : electrode part number t dlp11s 0.82 0.1 dlp11r 0.5 0.1 dlp11t 0.3 0.05 (1) (4) (2) (3) no polarity. impedance ( ? ) frequency (mhz) 1 10 100 1000 10000 1 10 100 1000 10000 common mode differential mode dlp11sn670sl2 dlp11sn281hl2 dlp11sn241hl2 dlp11sn281hl2 dlp11sn331hl2 dlp11sn201hl2 dlp11sn201hl2 dlp11sn241hl2 dlp11sn331hl2 dlp11sn900hl2 dlp11sn121sl2 dlp11sn161sl2 dlp11sn670sl2 dlp11sn900hl2 dlp11sn121sl2 dlp11sn161sl2 impedance ( ? ) frequency (mhz) 1 10 100 1000 1 10 100 1000 10000 dlp11sa900hl2 dlp11sa670hl2 dlp11sa350hl2 dlp11sa900hl2 dlp11sa670hl2 dlp11sa350hl2 common mode differential mode impedance ( ? ) frequency (mhz) 1 10 100 1000 1 1 0 100 1000 10000 dlp11rn450ul2 dlp11rn450ul2 common mode differential mode impedance ( ? ) frequency (mhz) 1 10 100 1000 1 10 100 1000 10000 common mode differential mode dlp11rb150ul2 dlp11rb400ul2 dlp11rb150ul2 dlp11rb400ul2 common mode choke coil film type dlp11s/dlp11r/dlp11t series (0504 size) dimensions equivalent circuit impedance-frequency characteristics (main items) dlp11sn series impedance-frequency characteristics (main items) dlp11sa series impedance-frequency characteristics (main items) dlp11rn series impedance-frequency characteristics (main items) dlp11rb series continued on the following page.
continued from the preceding page. http://www.murata.com/ data sheet ! note: 1. this datasheet is downloaded from the website of murata manufacturing co., ltd. therefore, it?s specifications are subject t o change or our products in it may be discontinued without advance notice. please check with our sales representatives or product engineers bef ore ordering. 2. this datasheet has only typical specifications because there is no space for detailed specifications. therefore, please appr ove our product specifications or transact the approval sheet for product specifications before ordering. 2 o this data sheet is applied for chip common mode choke coil used for general electronics equipment for your design. 2011.7.7 impedance ( ? ) frequency (mhz) 1 10 100 1000 1 10 100 1000 10000 common mode differential mode dlp11tb800ul2 dlp11tb800ul2 frequency (mhz) insertion loss (db) 0 2 4 6 8 10 1 10 100 1000 10000 dlp11sn900hl2 frequency (mhz) insertion loss (db) 0 2 4 6 8 10 1 10 100 1000 10000 dlp11sa900hl2 10 8 6 4 2 0 1 10 100 1000 10000 frequency (mhz) insertion loss (db) dlp11rn450ul2 frequency (mhz) 10 8 6 4 2 0 1 10 100 1000 10000 insertion loss (db) dlp11rb400ul2 noise suppression products/emi suppression filters > common mode choke coil > film type impedance-frequency characteristics (main items) dlp11tb series differential mode transmission characteristics (typ.) dlp11sn series differential mode transmission characteristics (typ.) dlp11sa series differential mode transmission characteristics (typ.) dlp11rn series differential mode transmission characteristics (typ.) dlp11rb series continued on the following page.
continued from the preceding page. http://www.murata.com/ data sheet ! note: 1. this datasheet is downloaded from the website of murata manufacturing co., ltd. therefore, it?s specifications are subject t o change or our products in it may be discontinued without advance notice. please check with our sales representatives or product engineers bef ore ordering. 2. this datasheet has only typical specifications because there is no space for detailed specifications. therefore, please appr ove our product specifications or transact the approval sheet for product specifications before ordering. 3 o this data sheet is applied for chip common mode choke coil used for general electronics equipment for your design. 2011.7.7 frequency (mhz) 10 8 6 4 2 0 1 10 100 1000 10000 insertion loss (db) dlp11tb800ul2 noise suppression products/emi suppression filters > common mode choke coil > film type differential mode transmission characteristics (typ.) dlp11tb series packaging code packaging minimum quantity l 180mm embossed tape 3000 (dlp11s) 4000 (dlp11r) 5000 (dlp11t) b bulk(bag) 500 rated value ( p : packaging code) part number common mode impedance (at 100mhz/20 dlp11sn670sl2 p 67ohm 20% 180ma 5vdc 100m ohm 12.5vdc 1.3ohm 25% -40 to +85 c dlp11sn121sl2 p 120ohm 20% 140ma 5vdc 100m ohm 12.5vdc 2.0ohm 25% -40 to +85 c dlp11sn161sl2 p 160ohm 20% 120ma 5vdc 100m ohm 12.5vdc 2.7ohm 25% -40 to +85 c dlp11sn900hl2 p 90ohm 20% 150ma 5vdc 100m ohm 12.5vdc 1.5ohm 25% -40 to +85 c dlp11sn201hl2 p 200ohm 20% 110ma 5vdc 100m ohm 12.5vdc 3.1ohm 25% -40 to +85 c dlp11sn241hl2 p 240ohm 20% 100ma 5vdc 100m ohm 12.5vdc 3.5ohm 25% -40 to +85 c dlp11sn281hl2 p 280ohm 20% 90ma 5vdc 100m ohm 12.5vdc 4.2ohm 25% -40 to +85 c dlp11sn331hl2 p 330ohm 20% 80ma 5vdc 100m ohm 12.5vdc 4.9ohm 25% -40 to +85 c dlp11sa350hl2 p 35ohm 20% 170ma 5vdc 100m ohm 12.5vdc 0.9ohm 25% -40 to +85 c dlp11sa670hl2 p 67ohm 20% 150ma 5vdc 100m ohm 12.5vdc 1.2ohm 25% -40 to +85 c dlp11sa900hl2 p 90ohm 20% 150ma 5vdc 100m ohm 12.5vdc 1.4ohm 25% -40 to +85 c dlp11rn450ul2 p 45ohm 25% 100ma 5vdc 100m ohm 12.5vdc 0.8ohm 25% -40 to +85 c dlp11rb150ul2 p 15ohm 5ohm 100ma 5vdc 100m ohm 12.5vdc 0.8ohm 25% -40 to +85 c dlp11rb400ul2 p 40ohm 10ohm 100ma 5vdc 100m ohm 12.5vdc 1.3ohm 25% -40 to +85 c dlp11tb800ul2 p 80ohm 25% 100ma 5vdc 100m ohm 12.5vdc 1.5ohm 25% -40 to +85 c number of circuit: 1 differential mode to common mode conversion characteristic (scd21) at 2.5ghz: -40db (typ./dlp11tb800ul2) impedance characteristics between signal lines z0 (tdr at 50ps): 90ohm 15ohm (dlp11tb800ul2) ! caution (rating) do not use products beyond the rated current and rated voltage as this may create excessive heat and deteriorate the insulation resistance. notice solderability of tin plating termination chip might be deteriorated when low temperature soldering profile where peak solder temperature is below the tin melting point is used. please confirm the solderability of tin plating termination chip before use. ! caution/notice
http://www.murata.com/ data sheet ! note: 1. this datasheet is downloaded from the website of murata manufacturing co., ltd. therefore, it?s specifications are subject t o change or our products in it may be discontinued without advance notice. please check with our sales representatives or product engineers bef ore ordering. 2. this datasheet has only typical specifications because there is no space for detailed specifications. therefore, please appr ove our product specifications or transact the approval sheet for product specifications before ordering. 1 o this data sheet is applied for chip common mode choke coil used for general electronics equipment for your design. 2011.5.12 noise suppression products/emi suppression filters > common mode choke coil > film type (array) 0.82 0.1 0.25 0.1 0.5 0.1 (1) (2) (3) (4) (5) (6) (7) (8) 2.0 0.1 1.0 0.1 0.25 0.15 (in mm) : electrode (1) (5) (6) (7) (8) (2) (3) (4) no polarity. frequency (mhz) impedance ( ? ) 1000 100 10 1 1 10 100 1000 10000 dlp2ada900hl4 common mode differential mode dlp2ada900hl4 dlp2ada670hl4 dlp2ada350hl4 dlp2ada670hl4 dlp2ada350hl4 impedance ( ? ) frequency (mhz) 1 10 100 1000 10000 1 10 100 1000 10000 dlp2adn281hl4 dlp2adn281hl4 differential mode common mode dlp2adn241hl4 dlp2adn201hl4 dlp2adn161hl4 dlp2adn121hl4 dlp2adn900hl4 dlp2adn670hl4 dlp2adn241hl4 dlp2adn201hl4 dlp2adn161hl4 dlp2adn121hl4 dlp2adn900hl4 dlp2adn670hl4 frequency (mhz) insertion loss (db) 0 2 4 6 8 10 10 100 1000 10000 dlp2ada900hl4 frequency (mhz) insertion loss (db) 0 2 4 6 8 10 1 10 100 1000 10000 dlp2adn900hl4 common mode choke coil film type (array) dlp2ad series (0804 size) dimensions equivalent circuit impedance-frequency characteristics (main items) dlp2ada series impedance-frequency characteristics (main items) dlp2adn series differential mode transmission characteristics (typ.) dlp2ada series differential mode transmission characteristics (typ.) dlp2adn series continued on the following page.
continued from the preceding page. http://www.murata.com/ data sheet ! note: 1. this datasheet is downloaded from the website of murata manufacturing co., ltd. therefore, it?s specifications are subject t o change or our products in it may be discontinued without advance notice. please check with our sales representatives or product engineers bef ore ordering. 2. this datasheet has only typical specifications because there is no space for detailed specifications. therefore, please appr ove our product specifications or transact the approval sheet for product specifications before ordering. 2 o this data sheet is applied for chip common mode choke coil used for general electronics equipment for your design. 2011.5.12 noise suppression products/emi suppression filters > common mode choke coil > film type (array) packaging code packaging minimum quantity l 180mm embossed tape 3000 b bulk(bag) 500 rated value ( p : packaging code) part number common mode impedance (at 100mhz/20 dlp2ada350hl4 p 35ohm 20% 150ma 5vdc 100m ohm 12.5vdc 0.8ohm 25% -40 to +85 c dlp2ada670hl4 p 67ohm 20% 130ma 5vdc 100m ohm 12.5vdc 1.0ohm 25% -40 to +85 c dlp2ada900hl4 p 90ohm 20% 120ma 5vdc 100m ohm 12.5vdc 1.4ohm 25% -40 to +85 c dlp2adn670hl4 p 67ohm 20% 140ma 5vdc 100m ohm 12.5vdc 1.3ohm 25% -40 to +85 c dlp2adn900hl4 p 90ohm 20% 130ma 5vdc 100m ohm 12.5vdc 1.7ohm 25% -40 to +85 c dlp2adn121hl4 p 120ohm 20% 120ma 5vdc 100m ohm 12.5vdc 2.0ohm 25% -40 to +85 c dlp2adn161hl4 p 160ohm 20% 100ma 5vdc 100m ohm 12.5vdc 2.5ohm 25% -40 to +85 c dlp2adn201hl4 p 200ohm 20% 90ma 5vdc 100m ohm 12.5vdc 3.2ohm 25% -40 to +85 c dlp2adn241hl4 p 240ohm 20% 80ma 5vdc 100m ohm 12.5vdc 3.8ohm 25% -40 to +85 c dlp2adn281hl4 p 280ohm 20% 80ma 5vdc 100m ohm 12.5vdc 4.6ohm 25% -40 to +85 c number of circuit: 2 ! caution (rating) do not use products beyond the rated current and rated voltage as this may create excessive heat and deteriorate the insulation resistance. notice solderability of tin plating termination chip might be deteriorated when low temperature soldering profile where peak solder temperature is below the tin melting point is used. please confirm the solderability of tin plating termination chip before use. ! caution/notice
|
